Delrin Accelerator Pedal Bushing
Delrin Accelerator Pedal BushingDelrin Accelerator Pedal BushingDelrin Accelerator Pedal Bushing

Garagistic

SKU:K0090-DL

$55.95

  • Premium Products. Great Prices.

  • Aussie Owned - Locally Stocked

  • *4-week "No-Risk" Refund Promise on Pre-Orders - Excludes Special Orders

Delrin Accelerator Pedal Bushing

BMW DELRIN ACCELERATOR BUSHINGS (35411119016)

One of the most neglected bushings on your classic BMW is this little accelerator bushing that connects the throttle linkage under the dash. This can cause a sloppy accelerator feel and at times, squeak when the gas pedal is pushed. The original bushings have been pushed thousands of times. Sure, you can replace it with another OEM unit (part number 35411119016). But even the new units are very soft. Do it once, do it right. by using our Delrin accelerator bushings as a replacement to the stock bushings, this is a permanent fix! Comes with an installation tool, for a simplified install. Lubricate with lithium grease on installation to ensure quiet service for years to come.

Compatibility

  • Fits BMWs that have the bushing 35411119016. Please check on realoem.com before ordering to make sure that this will work on your car.
  • E30: 84-92 ALL
  • E34: 89-95 (530i &535i) (will not fit E34 M5)
  • E24: 77-86 (628, 633, 635, M6)
  • E28: ALL

Looking for an E36 Accelerator Pedal Bushing? You can find it here: https://www.garagistic.com/products/delrin-accelerator-pedal-bushing-10-2-mm-diameter-e36-z3?_pos=1&_sid=fe0d39ec4&_ss=r

Note: Must be lubricated on installation. COMES WITH TOOL FOR EASY INSTALLATION.

What's Included?

  • Accelerator bushing (BMW part number 35411119016)
  • Installation tool

Instructions

**THIS PROCESS WILL DIFFER DEPENDING ON YOUR CHASSIS**

Step 1: Remove the accelerator pedal by removing the c-clip or pushing in the pin on the back right side of the pedal followed by the bottom clip behind the pedal.

Step 2: Remove the throttle cable from the bracket

Step 3: Locate and remove the accelerator pedal pivot bracket clip holding it in place, this will allow you to remove the assembly

Step 4: Remove the old worn out bushings

Step 5: Grab the bolt and one washer from the provided press tool. Put the washer on the bolt followed by one of the bushings with the flat side towards the washer.

Step 6: Place the cup from the press tool over the lip, if your vehicle does not have the lip it will be on the outside. The inside referring to the middle of the accelerator bracket.

Step 7: Take the bolt with the washer and bushing and insert it from the opposite side of the cup and place the other washer and nut and hand tighten it.

Step 8: Hold one end and tighten the other side and the bushing will start to press in.

Will this fit my car?


The fastest way to confirm fitment is by using RealOEM with the last 7 digits of your VIN.
If you’re unsure or just want a second set of eyes, shoot us an email at sales@bavarianspeed.com.au. 


How long until it ships?


In stock items usually within 24 hours. OEM Pre-order items typically arrive within 2-3 Weeks.

If timing matters, contact us and we’ll give you the most accurate lead time we can. No crystal ball, just real info.


Can't find the part you need?


Reach out with your VIN or part number and we’ll take it from there.


Why use Bavarian Speed Shop?

We’re a locally owned Australian business, genuine BMW enthusiasts, and we actually care about getting the right part to the right car.